Shop

You are here:
  1. Home
  2. Shop
  3. Page 34

KUKA 1FK7101-5AZ91-1ZZ9-Z S07

Product Name
KUKA 1FK7101-5AZ91-1ZZ9-Z S07 Permanent Magnet Synchronous Servo Motor
Product Overview
The 1FK7101-5AZ91-1ZZ9-Z S07 is a KUKA-specific permanent magnet synchronous servo motor based on the Siemens 1FK7 platform and intended for KUKA KR C4 and KR C5 robot joint drives. The ZS07 designation identifies a special shaft, connector and brake arrangement. The motor pairs with KUKA KSP40 and KSP64 servo drive modules.

EMERSON 1C31166G02

Product Name
Emerson 1C31166G02 Ovation Serial Link Controller
Product Overview
The 1C31166G02 is an Ovation serial-link-controller electronics module. It interfaces an Ovation controller with third-party devices through a serial communication personality module. The module is one element of a three-part assembly: a DIN-rail-mounted base unit, the 1C31166G02 electronics module, and a personality module that determines the physical serial interface and connector layout.

EMERSON 1C31122G02

Product Name
Emerson 1C31122G02 Ovation 16-Channel Digital Output Module
Product Overview
The 1C31122G02 is a 16-channel digital output module for the Emerson Ovation distributed control system. It converts controller output commands into discrete low-side switched signals for field-side loads such as solenoid valves, motor starter coils, alarms and indicators. The module installs directly into an Ovation I/O rack and communicates with the controller across the Ovation I/O bus.

ALLEN-BRADLEY 193-ECPM3

Product Overview
The 193-ECPM3 is a mechanical mounting adapter in the Bulletin 193 accessory family. It provides an independent panel or DIN-rail location for an E3 or E3 Plus solid-state overload relay, separating the relay body from the load-side contactor. This allows the relay display, full-load-ampere setting and test/reset access to be positioned at the panel door while the contactor remains mounted on the backplate. The adapter is a mechanical and power-conduction interface, not a protection device, and introduces no firmware, parameter set or network address.

ALLEN-BRADLEY 1794-OW8

Product Overview
The 1794-OW8 is an eight-point electromechanical relay output module in the Allen-Bradley Bulletin 1794 FLEX I/O family. It switches external AC or DC loads through eight individually isolated Form A (normally open) contacts. Because each contact is electrically separated from the FLEXBus logic and from the other seven contacts, the module is suited to mixed-voltage discrete control panels where genuine contact switching is required rather than a semiconductor output.

Applied Materials 0100-71278

Product Name​
VME Communication Interface Board with PMC Expansion.
Product Introduction​
This board acts as a VME communication carrier for PMC mezzanine modules in Applied Materials and AKT CVD, PECVD, PVD, and flat panel display platforms. It aggregates process data and provides high speed interfacing between the host system and chamber or substrate handling hardware.

Applied Materials 0100-71275

Product Name​
VME P2 Backplane and CVD Communication Interface Module.
Product Introduction​
Public sources list this number as an AKT VME P2 backplane or communication interface module for 60K CVD systems, providing interboard data exchange and power distribution. Some sources also describe it more generally as a vacuum chamber control module, so confirm the exact role from the system drawing.

Applied Materials 0100-71271

Product Name​
VMEbus Digital I/O Module.
Product Introduction​
This module provides digital input acquisition and digital output control for VMEbus based semiconductor and flat panel display systems. It interfaces external switches, sensors, valves, indicators, and interlock devices with the host controller.

Applied Materials AKT 0100-71229

Product Name​
AKT System Auxiliary CPU or Logic Board.
Product Introduction​
Public detailed electrical datasheet for this exact number is limited. Related AKT platform listings identify 0100-71229 as an auxiliary or main CPU board used with VME communication carriers, digital I/O, and PMC modules in CVD, PECVD, and flat panel display tools.

Applied Materials 0100-71224

Product Name​
Digital Counter and Logic Signal Interface Board.
Product Introduction​
This board provides high precision pulse counting, discrete digital I/O routing, and logic interfacing within Applied Materials legacy semiconductor tool racks, including CVD, etch, and subassembly control platforms.

Applied Materials 0100-09123

Product Name​
P5000 Wafer Sensor Board.
Product Introduction​
This board detects wafer presence and position in Applied Materials P5000 Precision 5000 platforms. It provides sensing signals for transfer interlocks, process monitoring, and tool automation.

Applied Materials 0090-07135

Product Name​
ATCA Process Control Compute Module, public alternate listing as RF Impedance Matching Component.
Product Introduction​
Public supplier data lists this number as an AdvancedTCA semiconductor process controller with processor, memory, and communication interfaces. Separate low detail sources list it for RF impedance matching in etch systems. Confirm the exact hardware from the tool nameplate and schematic.