Shop

You are here:
  1. Home
  2. Shop
  3. Page 755

GE IC697CPX772HD CPU Module

  • Processor: 96 MHz, 80486 DX4 microprocessor.
  • Memory: 512 KB of battery - backed RAM and 256 KB of non - volatile flash memory.
  • I/O Capacity: Supports up to 2000 discrete I/O (any combination) and up to 8000 analog I/O.
  • Communication Ports: Has three serial ports, including one RS - 232 (6 - pin RJ - 11) and two RS - 485 (15 - pin D - shell) ports.
  • Power Supply: 5V DC input.
  • Current Draw: 3.1 amps.
  • Operating Temperature Range: 0°C to 60°C.

GE IC697CGR772AA Hot Standby Genius Dual Bus CPU Module

  • Processor: 96 MHz, 32 - bit floating - point processor.
  • Memory: 512 kbytes of battery - backed fast CMOS RAM.
  • I/O Capacity: Supports up to 2,048 inputs and 2,048 outputs, and up to 8 k analog I/O.
  • Communication Interface: Has three serial ports.
  • Power Supply: Requires an isolated source and 5V DC for external power options with a lithium battery.

GE IC695ETM001 Ethernet Interface Module

Technical Specifications
 
  • Ethernet Ports: 2x 10/100 Mbps auto - sensing ports with RJ - 45 connectors.
  • Serial Port: RS - 232 (DCE), data rate from 1200 bps to 115200 bps, 9 - pin female D - connector.
  • Processor Speed: 200 MHz.
  • Dimensions: Approximately 3.8 cm x 13.3 cm x 13.3 cm.
  • Weight: About 0.2 kg.
  • Power Supply: Derived from the PLC backplane.
  • Operating Temperature Range: - 20°C to 70°C.

GE IC693374-HW Digital Output Module

  • Compatibility: Exclusively designed for GE Fanuc Series 90-30 PLC systems
  • Output Type: Relay outputs (electromechanical relays for switching AC/DC loads)
  • Number of Output Channels: 8 independent digital output channels
  • Output Voltage Ratings: Supports both AC and DC loads; AC: 120V AC / 240V AC, DC: 24V DC / 48V DC
  • Output Current Rating: Maximum 5A per channel (resistive load); 2A per channel (inductive load)
  • Power Supply: Derives power from the Series 90-30 PLC backplane (5V DC logic power); load power supplied externally
  • Isolation: Channel-to-channel isolation (250V AC rms) and channel-to-backplane isolation (500V AC rms)
  • Operating Temperature Range: 0°C to 60°C (32°F to 140°F)

GE IC693CHS391L

  • Number of Slots: It has 10 slots in total, with slot 1 dedicated for a plug - in CPU module.
  • Power Requirements: It uses 420 mA of internal power at 5 VDC.
  • Connector: It is equipped with a 25 - pin female connector.
  • Mounting Method: Panel mounting.

GE IC660TBD120 Timer/Counter Base Module

  • Compatibility: Exclusively designed for GE Series 90-30 PLC systems
  • Power Supply: Draws power from the Series 90-30 PLC backplane (no external power required)
  • Module Type: Passive base module (requires a compatible timer/counter plug-in module for functionality)
  • Mounting: Installs directly into the Series 90-30 PLC I/O rack, occupying 1 slot in the rack
  • Backplane Interface: Complies with Series 90-30 backplane communication protocols for data exchange with the PLC CPU
  • Operating Temperature Range: 0°C to 60°C (32°F to 140°F)
  • Storage Temperature Range: -40°C to 85°C (-40°F to 185°F)
  • Humidity Resistance: 5% to 95% non-condensing
  • Physical Dimensions: Standard Series 90-30 module size (approx. 101.6mm width × 152.4mm height × 101.6mm depth, subject to GE’s standard specifications)

GE IC600BF801K Remote I/O Receiver Module

  • Power Requirements: It can handle up to 42 units of load at 5V DC, and 10 units of load at both 12V DC and -12V DC.
  • Connectors: Equipped with two edge - mounted D - type connectors.
  • LED Indicators: There are 4 LED indicators, including local ok, link ok, remote ok, and remote parity.
  • Installation Location: It should be installed in the left slot of the first I/O rack in a remote I/O station.
  • I/O Address: Not required.

GE 531X139APMAJG2 Servo Drive Module

  • Input Power: Three - phase 200 - 240 VAC, 50/60 Hz
  • Rated Output Current: 15 A (continuous), 30 A (peak)
  • Rated Output Power: 4.0 kW (depending on the motor and voltage)
  • Control Mode: Torque control, speed control, position control (supporting pulse/direction, analog command)
  • Feedback Interface: Supports incremental encoders, absolute encoders (multi - turn/single - turn)
  • Communication Interface: Optional modules support Profibus - DP, DeviceNet, Modbus TCP/IP
  • Control Power: 24 VDC (±10%)
  • Protection Functions: Over - current, over - voltage, under - voltage, over - heat, short - circuit, ground - fault protection
  • Protection Level: IP20 (installed in the control cabinet)
  • Operating Environment Temperature: 0°C to +55°C
  • Storage Temperature: - 25°C to +85°C
  • Dimensions (W x H x D): Approximately 75mm x 245mm x 195mm
  • Weight: Approximately 1.8 kg

GE 44A390410 - G01 Output Board

Functional Features
 
  • Reliable Output: It is designed to provide stable and reliable output signals to ensure the normal operation of external devices.
  • Compatibility: It has good compatibility with other components in the GE control system, which is convenient for system integration.

GE IC693374 - CJ Digital Input Module

  • Input Channels: Usually has 16 input channels.
  • Input Voltage: For example, it may support 24V DC input voltage, but the specific value may vary depending on the actual model and configuration.
  • Response Time: The response time can be very fast, such as less than 1 millisecond, which is suitable for applications requiring quick signal acquisition.
  • Isolation Voltage: Generally has a certain isolation voltage, such as 1500V AC, to ensure the safety and stability of the signal.

GE IC698CRE020-GG Redundancy CPU Module

  • Processor Speed: 700 MHz
  • User Memory: 10 MB
  • Operating Temperature: 0℃ - 60℃ (32 - 140 degrees Fahrenheit)
  • Relative Humidity: 5 - 95% (non - condensing)
  • Number of Serial Ports: 3 (including an RS - 232 port, an RS - 485 port, and an RS - 232 Ethernet station manager port)
  • Ethernet Interface: Dual RJ - 45 ports with auto - sensing, supporting 10/100/1000BaseT Ethernet

GE IC086SLN042 - A Data Transmission Module

  • Communication Interfaces: It is likely to support 多种通信协议，such as RS - 485, CAN bus, etc., based on the similar models IC086SLN042SS.
  • Power Supply: Not explicitly mentioned, but similar modules usually have a specific power input requirement.
  • Number of Channels: It can simultaneously process multiple data channels, but the exact number is not clearly stated.