Shop

You are here:
  1. Home
  2. Shop
  3. Page 552

GE IC693CMM321 Communication Module

Technical Specifications
 
  • Power Supply Voltage: 24V DC
  • Power Current: 5A
  • Operating Temperature Range: -20°C to 70°C
  • Storage Temperature Range: -40°C to 85°C
  • Humidity Range: 5% to 95% (non - condensing)
  • Vibration Resistance: 5g peak (10 to 500Hz)
  • Shock Resistance: 15g (11ms)
  • Dimensions: 100mm x 60mm x 25mm
  • Weight: 200g
  • Interface Type: 37 - pin D - Sub connector
  • Communication Interfaces: RS - 232, RS - 485, AAUI port
  • Communication Protocols: Supports GE Fanuc SNP, Modbus, DF1, etc.
  • Data Transmission Rate: Up to 9600 bps

GE IS200DSPXH1DBD Digital Signal Processor Module

echnical Specifications
 
  • Processor: Built - in 3 digital signal processors with programmable processor clock rate.
  • Data Format: Supports various data formats, such as 32 - bit floating - point numbers and 16 - bit integers.
  • Communication Protocol: Supports multiple communication protocols, like Modbus and DeviceNet.

GE IC754VGF12CTD-FC

  • Display Size: 12 inches.
  • Display Type: Color TFT.
  • Resolution: 800×600 pixels.
  • Color Depth: 16 bits per pixel, a total of 65,536 colors.
  • Communication Interfaces: RS - 232, RS - 485, Ethernet.
  • Input Power: 12 or 24 VDC.
  • Memory: 64 MB.
  • Processor: XScale processor.

GE IC752WBB202DVME

Technical Specifications
 
  • Power Requirement: Usually requires a +5V power supply with a certain tolerance, such as +5V ± 5%.
  • Operating Temperature Range: Can typically operate in a wide temperature range, for example, -25°C to +75°C, and some may support an extended range of -45°C to +85°C.
  • Power Consumption: Generally has relatively low power consumption, such as around 6.0W (typical).

GE IC698PSA100C Power Supply Module

  • Input Voltage Range: 85 - 264 VAC (nominal 120/240 VAC) or 100 - 150 VDC (nominal 125 VDC).
  • Output Voltage: +5 VDC, +12 VDC, -12 VDC.
  • Output Current: Up to 20 A (+5 VDC), up to 2 A (+12 VDC), up to 1 A (-12 VDC).
  • Power Output: Maximum 100 watts, distributed across three output terminals.
  • Efficiency: Greater than 85%.
  • Operating Temperature Range: 0°C - 60°C.
  • Storage Temperature Range: -40°C - 85°C.
  • Dimensions: 150 mm x 100 mm x 50 mm.
  • Weight: Approximately 1 kg.

GE IC697CPX772HD CPU Module

  • Processor: 96 MHz, 80486 DX4 microprocessor.
  • Memory: 512 KB of battery - backed RAM and 256 KB of non - volatile flash memory.
  • I/O Capacity: Supports up to 2000 discrete I/O (any combination) and up to 8000 analog I/O.
  • Communication Ports: Has three serial ports, including one RS - 232 (6 - pin RJ - 11) and two RS - 485 (15 - pin D - shell) ports.
  • Power Supply: 5V DC input.
  • Current Draw: 3.1 amps.
  • Operating Temperature Range: 0°C to 60°C.

GE IC697CGR772AA Hot Standby Genius Dual Bus CPU Module

  • Processor: 96 MHz, 32 - bit floating - point processor.
  • Memory: 512 kbytes of battery - backed fast CMOS RAM.
  • I/O Capacity: Supports up to 2,048 inputs and 2,048 outputs, and up to 8 k analog I/O.
  • Communication Interface: Has three serial ports.
  • Power Supply: Requires an isolated source and 5V DC for external power options with a lithium battery.

GE IC695ETM001 Ethernet Interface Module

Technical Specifications
 
  • Ethernet Ports: 2x 10/100 Mbps auto - sensing ports with RJ - 45 connectors.
  • Serial Port: RS - 232 (DCE), data rate from 1200 bps to 115200 bps, 9 - pin female D - connector.
  • Processor Speed: 200 MHz.
  • Dimensions: Approximately 3.8 cm x 13.3 cm x 13.3 cm.
  • Weight: About 0.2 kg.
  • Power Supply: Derived from the PLC backplane.
  • Operating Temperature Range: - 20°C to 70°C.

GE IC693374-HW Digital Output Module

  • Compatibility: Exclusively designed for GE Fanuc Series 90-30 PLC systems
  • Output Type: Relay outputs (electromechanical relays for switching AC/DC loads)
  • Number of Output Channels: 8 independent digital output channels
  • Output Voltage Ratings: Supports both AC and DC loads; AC: 120V AC / 240V AC, DC: 24V DC / 48V DC
  • Output Current Rating: Maximum 5A per channel (resistive load); 2A per channel (inductive load)
  • Power Supply: Derives power from the Series 90-30 PLC backplane (5V DC logic power); load power supplied externally
  • Isolation: Channel-to-channel isolation (250V AC rms) and channel-to-backplane isolation (500V AC rms)
  • Operating Temperature Range: 0°C to 60°C (32°F to 140°F)

GE IC693CHS391L

  • Number of Slots: It has 10 slots in total, with slot 1 dedicated for a plug - in CPU module.
  • Power Requirements: It uses 420 mA of internal power at 5 VDC.
  • Connector: It is equipped with a 25 - pin female connector.
  • Mounting Method: Panel mounting.

GE IC660TBD120 Timer/Counter Base Module

  • Compatibility: Exclusively designed for GE Series 90-30 PLC systems
  • Power Supply: Draws power from the Series 90-30 PLC backplane (no external power required)
  • Module Type: Passive base module (requires a compatible timer/counter plug-in module for functionality)
  • Mounting: Installs directly into the Series 90-30 PLC I/O rack, occupying 1 slot in the rack
  • Backplane Interface: Complies with Series 90-30 backplane communication protocols for data exchange with the PLC CPU
  • Operating Temperature Range: 0°C to 60°C (32°F to 140°F)
  • Storage Temperature Range: -40°C to 85°C (-40°F to 185°F)
  • Humidity Resistance: 5% to 95% non-condensing
  • Physical Dimensions: Standard Series 90-30 module size (approx. 101.6mm width × 152.4mm height × 101.6mm depth, subject to GE’s standard specifications)

GE IC600BF801K Remote I/O Receiver Module

  • Power Requirements: It can handle up to 42 units of load at 5V DC, and 10 units of load at both 12V DC and -12V DC.
  • Connectors: Equipped with two edge - mounted D - type connectors.
  • LED Indicators: There are 4 LED indicators, including local ok, link ok, remote ok, and remote parity.
  • Installation Location: It should be installed in the left slot of the first I/O rack in a remote I/O station.
  • I/O Address: Not required.