Shop

You are here:
  1. Home
  2. Shop
  3. Page 244

Kollmorgen PRD-0016600D-15

Model Code Breakdown:

  • PRD: Product Series — Multi-Turn Absolute Position Feedback Device
  • 0016600: 16,600 Counts per Revolution (Effective Resolution)
  • D: Multi-Turn Capability (D = Digital Multi-Turn, Up to 4096 Revolutions)
  • 15: Configuration Code (Output Protocol / Electrical Interface)

Kollmorgen S74802-NANAPM

Model Code Breakdown:

  • S7: S700 Series
  • 48: Frame Size (48 = 115 mm Flange, S700 Medium Frame)
  • 02: Stack Length Code (02 = Short Stack, Low Inertia)
  • NA: No-Key Shaft (Smooth, Clamping Hub Mount)
  • NA: No-Key Shaft (Confirmed — Double NA indicates smooth shaft both ends or specific shaft spec)
  • PM: Permanent Magnet (Standard NdFeB, Not High-Temperature Variant)

Kollmorgen 63032-01C

Model Series: 63032 Series Absolute Encoder Model Code Breakdown:

  • 63032: Series Designation
  • 01: Variant Code (Electrical/Mechanical Configuration)
  • C: Output Protocol — BiSS-C (Bidirectional Synchronous Serial)

Kollmorgen 63032-01C

Model Code Breakdown:

  • AKD: Drive Series
  • B: Base Configuration (Standard Feature Set)
  • 024: 24 VDC Nominal DC Bus Voltage
  • 07: 7 A RMS Continuous Output Current
  • NCS: Configuration Code (Network: EtherCAT, Command: Cyclic Synchronous, Analog I/O: Standard with Safe Torque Off)

Kollmorgen AKD-B02407-NCS

Model Code Breakdown:

  • AKD: Drive Series
  • B: Base Configuration (Standard Feature Set)
  • 024: 24 VDC Nominal DC Bus Voltage
  • 07: 7 A RMS Continuous Output Current
  • NCS: Configuration Code (Network: EtherCAT, Command: Cyclic Synchronous, Analog I/O: Standard with Safe Torque Off)

Kollmorgen 606-DD-99-TS-268

Model Code Breakdown:

  • 606: Motor Frame Series
  • DD: Double-Ended Shaft Configuration
  • 99: Winding Code (Specific Kv/Torque Constant Variant)
  • TS: Encoder Type — Single-Turn Absolute, 12-Bit (4096 Counts/Rev)
  • 268: Shaft/Connector Configuration Code

Kollmorgen 204-C-31-B3

Model Series: 204 Series Frameless Torque Motor Model Code Breakdown:

  • 204: Frame Size (2.04 inch / 51.8 mm Outer Diameter)
  • C: Motor Stack Length Variant (Medium Torque Version)
  • 31: Winding Configuration Code (Specific Kv/Torque Constant)
  • B3: Mounting Flange Type (B3 = Square Flange with Tapped Holes)

Kollmorgen AKD-P02407-NCA

Model Code Breakdown:

  • AKD: Drive Series
  • P: Power Module (Regenerative/Non-Regenerative Power Stage)
  • 024: 24 VDC Nominal DC Bus Voltage
  • 07: 7 A RMS Continuous Output Current
  • NCA: Configuration Code (Network: EtherCAT, Command: Profile Velocity/Torque, Analog I/O: Standard)

Kollmorgen S60600-600

Product Name: Kollmorgen AKM S600 Series Slotless Brushless Servo Motor Model Series: AKM S600 Series Product Type: Slotless Brushless DC Servo Motor Rated Power: 600 W (0.6 kW)

Kollmorgen AKM22E-ACC2R-0

Product Introduction: The AKM22E-ACC2R-0 is the smallest motor in Kollmorgen's AKM product family, designed for ultra-compact motion applications requiring precise positioning in minimal space. The "22" denotes the 22mm frame size, "E" indicates the motor length variant, "ACC" specifies a multi-turn absolute encoder, "2" is the 2500 RPM speed rating, "R" denotes the winding code, and "0" indicates a smooth (keyless) shaft with set-screw locking.

Kollmorgen AKM73P-ACC2GK0

Product Introduction: The AKM73P-ACC2GK0 is a compact brushless DC servo motor from Kollmorgen's AKM product family. The "73" denotes the 73mm frame size, "P" indicates an integrated holding brake, "ACC" specifies a multi-turn absolute encoder, "2" denotes the 2500 RPM speed rating, "G" indicates the winding variant, and "K0" specifies a keyed shaft output. This motor is designed for applications requiring failsafe holding when power is removed.

Kollmorgen B-102-A-21

Product Series: B-Series — Servo Motor Cable Assemblies Product Introduction: The B-102-A-21 is a pre-configured servo motor power cable assembly from Kollmorgen's B-Series product line. It is designed to connect Kollmorgen servo motors (AKM, AEM, XEL, XPL, AEP, ACM series) to AKD/AKM servo drives. The "102" indicates the cable cross-section and length code, "A" denotes the connector type, and "21" specifies the wiring configuration.