Shop

You are here:
  1. Home
  2. Shop
  3. Page 680

AEG AS-884A-201 High-Speed Counter Module

  • Product Introduction: It is a high-performance high-speed counter module of the AEG Modicon 884 series, specially designed for collecting high-frequency pulse signals from industrial field speed sensors, encoders and proximity switches. It can realize high-precision counting, frequency measurement and position detection, and transmit the collected data to the PLC CPU in real time to provide data support for the speed, position and displacement control of the equipment.
  • Technical Specifications:
    • Counting Channels: 4 independent high-speed counting channels, supporting single-phase and two-phase (A/B phase) pulse input.
    • Counting Frequency: Single-phase pulse maximum 500 kHz, two-phase A/B pulse maximum 250 kHz (4X quadrature decoding).
    • Counting Range: 32-bit signed integer, range from -2147483648 to 2147483647.

AEG AS-J540-100 Communication Interface Module

  • Product Introduction: It is a communication interface module designed for AEG Modicon series PLC, which can realize the data interaction between the PLC system and the upper‑level monitoring equipment (such as SCADA, HMI) through the Modbus TCP/IP protocol. It is the key component to realize the networking and remote monitoring of the industrial control system.
  • Technical Specifications:
    • Communication Protocol: Modbus TCP/IP, compatible with Modbus RTU protocol through protocol conversion.
    • Network Interface: 10/100 Mbps RJ45 Ethernet port, supporting full‑duplex communication.
    • Communication Distance: Up to 100 meters (twisted pair), supporting fiber‑optic extension.
    • Number of Connections: Up to 16 concurrent TCP connections.

AEG 120-166-006 Brushless Servo Motor

  • Product Introduction: It is a high‑performance brushless servo motor of the AEG Modicon 120 series, which integrates a permanent magnet rotor and a high‑precision encoder. It can realize high‑speed and high‑precision position, speed and torque control under the drive of the servo driver, and is used to drive the executive components in the industrial automation system to complete the precise motion control task.
  • Technical Specifications:
    • Rated Power: 0.75 kW; Rated Voltage: 220 VAC (three‑phase); Rated Current: 3.8 A.
    • Rated Speed: 3000 rpm; Maximum Speed: 6000 rpm; Rated Torque: 2.39 N·m.
    • Encoder: 2500‑line incremental encoder, supporting position feedback and speed measurement.
    • Protection Class: IP65 (motor body), IP20 (connector); Insulation Class: Class F.
    • Cooling Method: Forced air cooling; Weight: 5.2 kg; Dimensions: 110mm × 140mm (diameter × length).

AEG AS-B883-111 8‑Channel Analog Input Module

  • Product Introduction: It is an 8‑channel analog input module of the AEG Modicon 800 series, which is used to collect analog signals (voltage/current) from industrial field sensors such as temperature, pressure, flow, and level, convert them into 12‑bit digital signals through A/D conversion, and transmit them to the CPU module for data processing and control decision‑making.
  • Technical Specifications:
    • Input Channels: 8 independent analog input channels, supporting single‑ended or differential input switching.
    • Signal Types: Voltage (0‑5 VDC, 0‑10 VDC) and current (4‑20 mA) signals are optional.
    • Resolution: 12 bits; Conversion Accuracy: ±0.1% of full scale.
    • Conversion Time: ≤100 μs per channel.

AEG 1210880V5 Industrial Power Filter Module

  • Product Introduction: It is a power filter module designed for AEG industrial control equipment, which is used to filter out electromagnetic interference (EMI) and radio frequency interference (RFI) in the power supply line, protect the PLC, frequency converter and other precision equipment from the impact of grid noise, and ensure the stable and reliable operation of the equipment.
  • Technical Specifications:
    • Input Voltage: 220‑240 VAC, 50/60 Hz; Rated Current: 10 A.
    • Filtering Performance: It can suppress common‑mode and differential‑mode interference, and the attenuation of interference signals above 1 MHz is ≥40 dB.
    • Leakage Current: ≤1 mA; Response Time: ≤1 μs.

AEG 110‑222 Micro PLC Expansion Terminal Block

  • Product Introduction: It is a dedicated expansion terminal block for the AEG Modicon 110 series micro PLC, which is used to expand the external wiring interface of the PLC. It can connect multiple digital/analog I/O signals in a centralized manner, and realize the reliable transmission of field signals and PLC modules. It is an important accessory to ensure the stable operation of the small‑scale control system.
  • Technical Specifications:
    • Number of Terminals: 24 screw terminals, divided into 3 groups of 8 channels each, supporting mixed connection of input and output signals.
    • Rated Voltage: 250 VAC/30 VDC; Rated Current: 5 A per terminal.
    • Wiring Type: Screw clamping, suitable for wires with a cross‑section of 0.5‑2.5 mm².
    • Isolation: 1000 VAC isolation between terminal groups.
    • Operating Temperature: -20°C to +60°C; Protection Rating: IP20; Dimensions: 80mm × 50mm × 30mm (W×H×D); Material: Flame‑retardant ABS plastic.

AEG ALU821 Logic Arithmetic Unit Module

  • Product Introduction: It is an arithmetic logic unit module matched with AEG PLC, which is mainly used to perform high‑speed arithmetic operations (addition, subtraction, multiplication, division) and logic operations (AND, OR, NOT) on the data in the PLC system, and improve the data processing capability of the system, especially suitable for occasions that require complex data calculation and logic judgment.
  • Technical Specifications:
    • Operation Precision: 16‑bit fixed‑point arithmetic, supporting integer and BCD code operation.
    • Operation Speed: Arithmetic operation ≤1 μs per instruction, logic operation ≤0.5 μs per instruction.
    • Interface: Compatible with the AEG Modicon backplane bus, data transmission rate up to 1 Mbps.
    • Power Supply: 24 VDC, power consumption of 2 W.
    • Isolation: 1500 VDC isolation between the arithmetic unit and the system bus.
    • Operating Temperature: -20°C to +60°C; Dimensions: 100mm × 160mm × 50mm (W×H×D).

AEG CPU61203/110 Modicon Micro 110 Series CPU Module

  • Product Introduction: It is the core control component of the AEG Modicon Micro 110 series PLC, integrating a microprocessor, memory, and communication interface. It is responsible for executing user control programs, processing I/O data, and communicating with expansion modules and upper‑level devices, and is tailored for small‑scale industrial automation control scenarios.
  • Technical Specifications:
    • Processor: High‑performance 8‑bit microprocessor with a basic instruction execution time of ≤10 μs.
    • Memory: 4 KB user program memory and 2 KB data memory, supporting data retention when power is off.
    • Power Supply: 24 VDC, current consumption of 100 mA, power consumption of 2.4 W.
    • I/O Expansion: Supports connection to A120 series I/O expansion modules, with a maximum expandable I/O capacity of 64 points.

AEG AS-B809-016 16‑Channel 230 VAC Digital Input Module

  • Product Introduction: It is a 16‑channel digital input module belonging to the AEG Modicon 800 series, designed to collect 230 VAC switching signals from industrial field devices like limit switches, pushbuttons, and circuit breakers, and convert them into logic signals that can be identified by the PLC CPU for subsequent control logic operation.
  • Technical Specifications:
    • Input Channels: 16 independent digital input channels, divided into two common groups of 8 channels each.
    • Input Voltage: 160‑260 VAC, 47‑63 Hz; surge voltage: 400 VAC for 1 cycle, 300 VAC for 10 seconds.
    • Turn‑on Threshold: 112‑148 VAC; Turn‑off Threshold: 0‑90 VAC.
    • Typical Wetting Current: 8.5 mA at 230 VAC.
    • Response Time: ≤20 ms (on and off).

AEG AS-B805-016 Digital Input Module

  • Product Introduction: This is an 8 - channel digital input module of the AEG AS series. It is used to collect digital signals from external devices such as limit switches, proximity switches, and push - buttons, and transmit them to the CPU module for processing.
  • Technical Specifications:
    • Input Channels: 8 independent digital input channels.
    • Input Type: Dry contact input, supporting both normally open and normally closed contacts.
    • Input Voltage: 24 VDC, with a voltage tolerance of 15-30 VDC.
    • Input Current: 5 mA per channel when on.
    • Response Time: ≤2 ms.

AEG D984-385 984 385D Digital Output Module

  • Product Introduction: This is a 16 - channel digital output module of the AEG 984 series PLC. It converts the digital signals output by the CPU module into switching signals to drive external devices such as contactors, relays, and solenoid valves.
  • Technical Specifications:
    • Output Channels: 16 independent digital output channels.
    • Output Type: Relay output, rated switching voltage: 250 VAC/30 VDC.
    • Rated Switching Current: 5 A per channel, 10 A per common terminal.
    • Response Time: ≤10 ms (on and off).
    • Isolation: 2500 VAC between channels and between channels and the power supply.
    • Power Supply: 24 VDC, power consumption of 4 W.
    • Operating Temperature: -20°C to +60°C, Protection Rating: IP20.
    • Dimensions: 120mm × 160mm × 50mm (W×H×D).

AEG MM-PMC2-400 Advanced Operator Interface Panel

  • Product Introduction: This is an upgraded version of the AEG MM - PMC2 series operator interface panel, with a larger display screen and more powerful functions. It is used for complex human - machine interaction tasks in industrial control systems, providing a more intuitive and convenient operation experience.
  • Technical Specifications:
    • Display: 10.4 - inch color TFT LCD screen with a resolution of 800×600 pixels and a backlight life of over 50,000 hours.
    • Input Methods: Touchscreen (resistive) and membrane keypad with 30 function keys.
    • Communication Interfaces: RS - 232, RS - 485, Ethernet, Profibus - DP, Modbus TCP/IP.
    • Power Supply: 24 VDC (10-30 VDC), power consumption of 25 W.
    • Operating Temperature: -25°C to +70°C, Protection Rating: IP65 (front panel), IP20 (rear).
    • Dimensions: 400mm × 300mm × 100mm (W×H×D), Weight: 3.5 kg.