Shop

You are here:
  1. Home
  2. Shop
  3. Page 693

Bently 330180-90-00

Product Introduction: 9 m system version for large machines or where the driver must be mounted in a remote instrument room. Shares the same panel-mount footprint and electrical specs with the 5 m unit.
Technical Specifications:
  • System Length: 9.0 m
  • Mounting: Panel
  • Supply: –24 VDC
  • Output: 7.87 V/mm
  • Operating Temperature: 0 °C to +65 °C

Bently 330180-51-05

Product Introduction: Agency-approved version of 330180-51-00 for worldwide hazardous-area installations. Adds ATEX, IECEx and CSA certifications while maintaining identical electrical specs.
Technical Specifications:
  • System Length: 5.0 m
  • Supply: –24 VDC
  • Output: 7.87 V/mm
  • Approvals: ATEX Ex ia IIC T4 Ga, IECEx, CSA Class I Div 2

Bently 330180-51-00

Product Introduction: Current revision of the DIN-rail 5 m Proximitor. Offers identical electrical performance to 330180-50-00 but with a DIN-rail clip integral to the housing for high-density cabinet installations.
Technical Specifications:
  • System Length: 5.0 m
  • Mounting: DIN-rail (TS-35) or panel
  • Supply: –24 VDC, 12 mA
  • Output: –2 to –18 VDC
  • Sensitivity: 7.87 V/mm
  • Frequency: 0 – 10 kHz

Bently 330180-51-000

Product Introduction: Mechanically identical to 330180-51-00 but shipped with an extra “0” suffix that was later dropped. Provides the same 5 m system length and DIN-rail mounting option.
Technical Specifications:
  • System Length: 5.0 m
  • Mounting: DIN-rail or panel
  • Supply: –24 VDC
  • Output: 7.87 V/mm
  • Operating Temperature: 0 °C to +65 °C

Bently 330180-50-00

Product Introduction: The 330180-50-00 is the signal-conditioning module that converts the high-frequency eddy-current signal from the probe into a calibrated DC voltage proportional to gap. It forms the “driver” half of the 3300 XL 8 mm proximity transducer system and is mounted in the instrument cabinet rather than on the machine.
Technical Specifications:
  • System Length: 5.0 m (probe + extension)
  • Supply Voltage: –24 VDC ±1 V, 12 mA typical
  • Output: –2 to –18 VDC linear over 2 mm range
  • Sensitivity: 7.87 V/mm (200 mV/mil)
  • Frequency Response: 0 – 10 kHz

Bently 330171-00-12-10-01-05

Product Introduction: Long-case 11 mm probe with factory-armored integral cable for maximum mechanical protection in high-stress areas.
Technical Specifications:
  • Case Length: 120 mm
  • Total Length: 1.0 m
  • Armor: Stainless-steel interlocked
  • Approvals: ATEX, IECEx, CSA

Bently 330171-00-08-20-02-00

Product Introduction: 2 m system version of the 11 mm probe for installations where the driver must be mounted farther from the machine.
Technical Specifications:
  • Total Length: 2.0 m
  • Case Length: 80 mm
  • Certifications: None

Bently 330171-00-08-10-02-00

Product Introduction: 11 mm diameter probe for high-stiffness applications where increased resistance to side loading or vibration is required. Offers the same 2 mm linear range as 8 mm probes.
Technical Specifications:
  • Probe Diameter: 11 mm
  • Thread: M14 × 1.5
  • Case Length: 80 mm
  • Total Length: 1.0 m
  • Certifications: None

Bently 330161-02-85-05-94-01-02

Product Introduction: Ultra-slim 5 mm probe for tight radial clearances. Reverse-mount version with 90° connector fits inside small turbine wheels or compressor impellers where axial space is minimal.
Technical Specifications:
  • Probe Diameter: 5 mm
  • Thread: M8 × 1 reverse
  • Case Length: 85 mm
  • Total Length: 1.0 m
  • Connector: 90° miniature coax

Bently 330130-085-02-05

Product Introduction: 8.5 m standard extension for installations where an extra 0.5 m reach is required without stepping up to the next standard length. Fully agency-approved for worldwide use.
Technical Specifications:
  • Length: 8.5 m
  • Impedance: 75 Ω
  • Temperature: –55 °C to +200 °C
  • Approvals: ATEX, IECEx, CSA

Bently 330130-080-12-05

Product Introduction: Combines armor and FluidLoc technologies in one 8 m cable for maximum mechanical and chemical protection. Certified for worldwide hazardous areas.
Technical Specifications:
  • Length: 8.0 m
  • Armor: Stainless-steel interlocked
  • Seal: FluidLoc barrier
  • Approvals: ATEX, IECEx, CSA

Bently 330130-080-10-00

Product Introduction: 8 m cable insulated with perfluoroalkoxy (PFA) for extended temperature exposure up to 260 °C. Ideal for exhaust-gas or steam environments where standard FEP would soften.
Technical Specifications:
  • Length: 8.0 m
  • Insulation: PFA
  • Temperature: –55 °C to +260 °C
  • Impedance: 75 Ω
  • Approvals: None