Shop

You are here:
  1. Home
  2. Shop
  3. Page 242

Kollmorgen AKM52K-SSS2S-06

  • Product Name:​ AKM™ Series AC Synchronous Servo Motor, Frame Size AKM52 (Flange 115 mm / 130 mm OD), Stack Length K (long), 480 V AC winding, resolver feedback, smooth shaft, no brake, M23 connector
  • Product Introduction:​ The AKM52 is a high-power-density permanent-magnet AC servo motor from Kollmorgen's AKM family. The "K" stack length gives the highest continuous torque in the AKM5 frame. "SSS2S-06" decodes approximately to: Standard (S) flange/IEC tolerance, Smooth shaft (S), Single resolver feedback (S), 2 = standard seal, S = no brake, -06 = 480 V winding / specific connector orientation.

Kollmorgen B-606-B-A9-B3-203

Product Introduction:​ The Goldline EB series are low-inertia, rare-earth magnet synchronous servo motors designed for high dynamic performance. The EB-606 frame is a mid-size NEMA 20 / IEC equivalent motor typically used with Kollmorgen ServoStar CD/S300/S600 drives. The suffix "-B" denotes stack length B (medium torque), and the option codes indicate resolver feedback, special connector/MS bayonet, and possibly a rear shaft or thermostat per customer specification.

Kollmorgen S60300-PB

Product Introduction:​ The S600 series is a fully digital single-axis servo drive designed to control synchronous (permanent magnet AC) and asynchronous (induction) servo motors. The S60300-PB variant includes a PROFIBUS DP interface for integration into Profibus-based automation networks. It is typically paired with Kollmorgen AKM, Goldline, or other 3-phase brushless servo motors.

Kollmorgen CR10260

Product Introduction:​ CR-prefixed parts in Kollmorgen's cable catalog are pre-manufactured interconnection cables for AKM servomotors — either power-only, feedback-only, or combo. CR10260 is a standard-length (verify from order — often 3 m / 6 m / 9 m selectable via suffix not shown here) shielded cable with Intercontec motor-side connector and drive-side flying leads or D-sub/M12 as applicable.

Kollmorgen TPAR3330-56

Product Introduction:​ TPAR prefix in Kollmorgen legacy catalogs refers to tachometer/generator or resolver-to-encoder adapter components used with Goldline motors. "3330-56" specifies the tach generator type (3300 series — 30 V/krpm typical) or cable/adapter part number. Often a separately-mounted DC tach or an adapter box for resolver-to-drive interfacing.

Kollmorgen MTC306A1-E2C1

  • Product Name:​ SERVOSTAR 306 (MT306A1) Digital Servo Amplifier, 6 A Peak / 3 A Continuous Equivalent
  • Product Introduction:​ The SERVOSTAR 300 series (predecessor to AKD) is a digital brushless servo drive. MT306A1 is the 115/230 VAC input version. "E2C1" denotes firmware revision / interface option (typically RS-232/485 + ±10 V analog command, resolver or encoder feedback).

Kollmorgen KC1-B00306-NCC

Product Introduction:​ The KC1 (Kollmorgen Control — 1st generation integrated PAC + drive) combined a KAS (Kollmorgen Automation Suite) programmable automation controller with an AKD-class servo drive on one module. "B00306" = 3 A continuous drive section; "NCC" = no fieldbus option card / standard I/O + CANopen or serial. This unit runs IEC 61131-3programs and controls one axis locally while communicating with upstream HMI/PLC.

Kollmorgen DH062M-22-1DDR

Product Introduction:​ The DH062 is a framed (housed) direct-drive rotary motor that couples directly to the load — eliminating gearboxes, belts, and couplings. The "M" denotes single-bearing housed version; "-22" typically indicates 220 V winding or specific stack/feedback config; "-1" = standard option set. Provides zero backlash, high stiffness, and exceptional repeatability

Kollmorgen MTB706SB2-H191-022

Product Introduction:​ This is a Kollmorgen-specified external braking resistor used to dissipate regenerative energy from decelerating servo motors when the DC bus voltage would otherwise rise to a fault level. The MTB prefix designates Motion Technology Brake resistor; "706" relates to AKD 6/12 A frame compatibility; "SB2" = Standard Brake Resistor, 2nd variant; H191-022 = resistance/power/cable configuration per Kollmorgen ordering system.

Kollmorgen S70602-PBNANA

  • Product Name:​ S700 Series Digital Servo Amplifier, 6 A Continuous, EtherCAT Interface
  • Product Introduction:​ The S70602-PBNANA is part of Kollmorgen's S700 (often cross-referenced with AKD-era replacements) high-performance digital servo amplifier line. It supports EtherCAT communication and is suitable for retrofitting or integrating with Kollmorgen AKM motors.

Kollmorgen AKM33C-ANCNR-00

Product Introduction:​ The AKM33C is a medium-frame (Size 33 = 70 mm square flange) permanent-magnet synchronous servomotor from Kollmorgen's AKM family. "ANCNR-00" decodes approximately as: A=AKM series, N=Standard winding (640 VDC bus max for C-winding), C=Connector (Intercontec), N=No brake, R=Resolver feedback (typical for -NR suffix), 00=Standard seal/shaft.

Kollmorgen AKD-P02406-NBA12

  • Product Name:​ AKD® Performance Servo Drive with EtherCAT, 120/240 VAC, 24 A Continuous
  • Product Introduction:​ The AKD-P is the performance variant of the AKD family, equipped with EtherCAT (or other fieldbus per suffix) communication. "NBA12" indicates EtherCAT interface, expanded I/O options, and extended functionality. Designed for high-dynamic multi-axis motion systems.