Shop

You are here:
  1. Home
  2. Shop
  3. Page 67

GE IC693CMM311F

  • Communication Protocols: Supports GE Fanuc CCM, RTU (Modbus) slave, and SNP protocols.
  • Ports: Has two serial ports. Port 1 supports RS - 232, and port 2 supports either RS - 232 or RS - 485.
  • Internal Power: 400 mA at 5 VDC.

GE IC693CMM301

  • Communication Protocols: Supports Modbus RTU and Modbus TCP.
  • Maximum Number of Connectable I/O Modules: Can connect up to 31 Genius I/O modules.
  • Network Interface: Provides a 10/100 Mbps Ethernet interface.
  • Power Voltage: DC 24V.
  • Power Consumption: ≤5W.
  • Operating Temperature Range: -40°C to +70°C.
  • Storage Temperature Range: -40°C to +85°C.
  • Relative Humidity: 5% to 95% (non - condensing).
  • Dimensions: 110 mm×75 mm×35 mm.
  • Weight: 300g.

GE IC693CHS398J

  • Number of Slots: 5 slots.
  • Power Requirement: 170 mA at 5 VDC.
  • Expansion Cable Length: The maximum interconnect cable length for the expansion system is 50 feet or 15 meters.
  • Connector Type: It is equipped with a 25 - pin female D - type I/O bus expansion connector.
  • Dimensions: 10.43 x 5.12 x 5.59 inches (L x H x D).

GE IC693CHS392C

  • Bus Interface: 25 - pin D - type female I/O bus expansion connector.
  • Operating Voltage: DC 24V (external power supply is required for powering input/output modules).
  • Power Consumption: Typical value < 5W (excluding connected modules).
  • Isolation Method: Optional opto - coupler isolation or transformer isolation.
  • Response Time: < 1ms (typical value).
  • Operating Temperature: - 20°C to 70°C (optional extended range).

GE IC693CHS391M

  • Number of Slots: It has a total of 10 slots.
  • CPU Slots: One slot is dedicated to the CPU module, specifically slot 1.
  • I/O Slots: There are 9 slots available for I/O modules or option modules.
  • Power Supply Slot: One slot is for the power supply module, located at the left - most position and not included in the slot count.
  • Current: The current rating is 420 milliamperes.
  • Voltage: It operates at 5 volts DC.
  • Connector: It is equipped with a 25 - pin female connector for connecting remote or expansion baseplates.
  • Dimensions: Approximately 14.2 cm x 44.3 cm x 13 cm (L x W x H).
  • Weight: Around 3 kg.

GE IC693CHS391H

  • Type: High - speed counter module
  • Channels: 4 channels
  • Counting Modes: Up, down, up/down, quadrature
  • Counting Frequency: Up to 1 MHz
  • Resolution: 32 bits
  • Input Types: TTL, HTL, NPN, PNP
  • Power Supply: 24 VDC
  • Dimensions: 114 mm (H) x 40 mm (W) x 125 mm (D)
  • Weight: 250 grams

GE IC693APU302R

  • Power Supply: It requires 5V DC from the backplane.
  • Operating Temperature: The operating temperature range is 0°C to 55°C.
  • Relative Humidity: 5% to 95% non - condensing.
  • Module Size: It is a single - slot module that can be installed in any Series 90 - 30 baseplate.
  • Communication Interface: Communicates with other devices through the backplane of the Series 90 - 30 PLC.
  • Cable Connection: A 24 - pin I/O cable is used for building custom - length cables, and there are three different kits available: crimp wire receptacle, solder eyelet receptacle, and IDC (ribbon) receptacle.

GE IC693APU302P

  • Power Supply: It requires 5V DC from the backplane.
  • Operating Temperature: The operating temperature range is 0°C to 60°C.
  • Communication Interface: Communicates with other devices through the backplane of the Series 90 - 30 PLC.
  • Cable Connection: A 24 - pin I/O cable is used for building custom - length cables, and there are three different kits available, including crimp wire receptacle, solder eyelet receptacle, and IDC (ribbon) receptacle.

GE IC693APU302M

  • Power Supply: Requires 5V DC from the backplane.
  • Operating Temperature: The operating temperature range is 0°C to 60°C.
  • Relative Humidity: 5% to 95% non - condensing.
  • Module Size: It is a single - slot module that can be installed in any Series 90 - 30 baseplate.
  • Communication Interface: Communicates with other devices through the backplane of the Series 90 - 30 PLC.
  • Cable Connection: A 24 - pin I/O cable is used for building custom - length cables, and there are three different kits available: crimp wire receptacle, solder eyelet receptacle, and IDC (ribbon) receptacle.

GE IC693APU302K

  • Power Supply: It requires 5V DC from the backplane.
  • Operating Temperature: The operating temperature range is 0°C to 55°C.
  • Relative Humidity: 5% to 95% non - condensing.
  • Module Size: It is a single - slot module that can be installed in any Series 90 - 30 baseplate.
  • Communication Interface: It can communicate with other devices through the backplane of the Series 90 - 30 PLC.
  • Cable Connection: A 24 - pin I/O cable is used for building custom - length cables, and there are three different kits available: crimp wire receptacle, solder eyelet receptacle, and IDC (ribbon) receptacle.

GE IC693ALG391E

  • Power Supply: Requires 24V DC from an isolated 24V DC on the backplane or a user - supplied source, and 5V DC from the backplane. The external supply voltage range is 20 to 30V DC with a 10% external supply voltage ripple.
  • Isolation: There is 1,500V isolation between the field and logic side.
  • Output Current Range: Can provide outputs in the ranges of 0 to 20 mA and 4 to 20 mA.
  • Output Voltage Range: Also supports voltage outputs in the ranges of 0 to 5V and 1 to 5V.
  • Resolution: The resolution of the converted signal is 12 - bit binary (1 part in 4,096).
  • Accuracy: At 25 °C (77 °F), the absolute accuracy is ± 8 µA for the 4 to 20 mA range and ± 10 µA for the 0 to 20 mA range.

GE IC693ALG391B

  • Power Supply: It requires 24V DC from an isolated 24V DC on the backplane or a user-supplied source, and 5V DC from the backplane.
  • Isolation: There is 1,500V isolation between the field and logic side.
  • Output Current Range: The module can provide outputs in the range of 0 to 20 mA.
  • Resolution: The resolution of the converted signal is 12 bits binary (1 part in 4,096).
  • Update Rate: Both channels are updated on every scan, which is about 5 milliseconds.
  • Data Format: User data in the %AQ registers is in a 16-bit 2’s complement format. The 13 most significant bits from the %AQ register are converted to sign magnitude by the PLC and sent to the module.