GE

You are here:
  1. Home
  2. GE
  3. Page 36

GE IC200PBI001-BE

  • Interface Type: PROFIBUS DP.
  • Communication Rate: Supports various communication rates including 960 kbps, 1.5 Mbps, 3 Mbps, and 6 Mbps.
  • Node Address: Ranges from 0 to 127.
  • Operating Temperature Range: -25°C to +60°C (-13°F to +140°F).
  • Protection Level: IP67.
  • Dimensions: 80 mm x 30 mm x 25 mm (3.15 inches x 1.18 inches x 0.98 inches).

GE IC200MDL650E

  • Output Points: 32 output points.
  • Output Type: Relay output.
  • Rated Voltage: The output can support a wide range of voltages, typically compatible with both AC and DC voltages. For example, it can handle voltages such as 5 to 265VAC and 5 to 30VDC.
  • Rated Current: Each point has a rated current. For instance, at 5 to 265VAC, the rated current is 2.0A for resistive loads, and at 5 to 30VDC, the rated current is also 2.0A for resistive loads.
  • Response Time: The module has a relatively fast response time, which allows for quick switching of the output states. The on - to - off and off - to - on response times are typically short, enabling timely control of the connected devices.
  • Isolation Voltage: It has isolation between channels, with a rated isolation voltage of 250VAC (continuous) and 1500VAC (for 1 minute) between groups.

GE IC200CHS003H

  • Communication Protocol: Supports RS-485 serial communication (half-duplex mode) as the primary interface
  • Data Transfer Rate: Adjustable baud rates including 1200 bps, 2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, and 115200 bps
  • Communication Distance: Up to 1200 meters (4000 feet) at lower baud rates (e.g., 1200 bps) when using shielded twisted-pair (STP) cables
  • Number of Nodes: Supports up to 32 devices on a single RS-485 network (compliant with EIA/TIA-485 standards)
  • Interface Type: Removable terminal block (3-pin) for RS-485 connections (A, B, GND)
  • Power Supply: Derived from the VersaMax Micro base unit; operates on 5 VDC (backplane power), with a maximum power consumption of 0.5 W

GE IC695CMM002

  • Communication Ports: It has 2 isolated serial ports, which can be configured as RS - 232 or RS - 485/422.
  • Protocol Support: Supports multiple protocols, including Modbus RTU, DF1, ASCII, Modbus Master/Slave, DNP3 Master/Slave, CCM Slave, and Serial I/O.
  • Baud Rate: The baud rate is configurable, up to 115200 bps.
  • Data Bits: Usually 7 or 8 bits, configurable.
  • Stop Bits: 1 or 2 bits, configurable.
  • Parity Bits: None, odd parity, or even parity.
  • Power Requirements: Powered by the PLC main unit.
  • Operating Temperature Range: - 25°C to + 60°C.
  • Storage Temperature Range: - 40°C to + 85°C.
  • Relative Humidity: 5% to 95% (non - condensing).
  • Certifications: CE, UL, CSA, etc.

GE IC200CHS006E

  • Compatibility: Designed to work with VersaMax communication modules such as IC200BEM002 (Profibus - DP network slave module), IC200BEM103 (DeviceNet network control module).
  • Dimensions: 66.8 mm x 133.4 mm x 70 mm (excluding the height of the DIN rail).
  • Operating Temperature: 0 to 60 °C.
  • Storage Temperature: - 40 to 85 °C.
  • Network Data Rate: For modules like IC200BEM002 connected to it, the network data rate can range from 9.6 Kbaud to 12 Mbaud.
  • Power Consumption: For the connected communication modules, the power consumption is up to 460 mA at 5 V output and up to 5 mA at 3.3 V output.

GE IC695ALG600-DD

  • Input Channels: It has eight general - purpose analog input channels and two cold - junction compensation (CJC) channels.
  • Input Signal Types: Supports a wide range of signal types, including voltage (±50mV, ±150mV, 0 - 5V, 1 - 5V, 0 - 10V, ±10V), current (0 - 20mA, 4 - 20mA, ±20mA), resistance (0 to 250/500/1000/2000/3000/4000Ohms), thermocouple (B, C, E, J, K, N, R, S, T), and RTD (PT385/3916, N618/672, NiFe518, CU426).
  • Power Requirements: Requires 3.3V (350mA) and 5V (400mA) power supplies, with a maximum power dissipation of 5.4W.
  • Operating Temperature: The operating temperature range is 0 - 60°C (32 - 140°F), and the storage temperature range is - 40 - 85°C (- 40 - 185°F).

GE IC600LX680

  • Memory Capacity: Offers 64K of logic memory and 16K of register memory.
  • Memory Storage Device: Uses CMOS RAM, and is backed up by a lithium - manganese dioxide battery to prevent data loss during power outages.
  • Data Format: Supports 16 - bit words of logic memory, and stores data in a table and scratchpad format.
  • Power Requirements: The specific power requirements are not clearly stated, but similar modules in the series typically require 5V DC and 12V DC power supplies.
  • Operating Temperature: The operating temperature range is 0 - 60 degrees Celsius.

GE IC693DSM314-AD

  • Control Axes: Supports multiple control axes (specific number not clearly defined in the available resources).
  • Input Signals: Can accept various types of input signals such as encoder pulses for position feedback.
  • Output Signals: Provides output signals for driving servo - motors or other actuators, with signal types suitable for motor control.
  • Communication Interface: Likely supports communication protocols such as RS - 485 or other industrial - standard protocols for connecting with other devices and controllers in the system.
  • Operating Voltage: Typically operates within the voltage range suitable for industrial control systems, such as 24VDC (exact value may need further confirmation).

GE IC693PCM300D

  • Communication Protocols: Supports multiple communication protocols, including Modbus Master/Slave and DNP3 Master/Slave.
  • Communication Tasks: Each communication port supports up to 64 communication tasks.
  • Status Bits: Each port has 224 module and communication status bits, which can use the I, M, T areas, and 128 module and communication control bits, which can use the Q, M, T areas.

GE IC693MDL753

  • Operating Voltage: 12 or 24 volts DC.
  • Output Voltage Range: 10.2 to 28.8 volts DC.
  • Output Current: 0.5 amps maximum per output point, 4 amps maximum per group.
  • Number of Outputs: 32 individual output channels, grouped into four isolated groups of eight.
  • Isolation: 1,500 V between field side and logic side, 250 V between groups.
  • Response Time: 0.5ms max. on and off response time.
  • Power Consumption: 260 ma max. from 5v bus on backplane (13 ma + 3 ma / point on + 4.7 ma / led).
  • Operating Temperature Range: -10 °C to +55 °C.
  • Storage Temperature Range: -40 °C to +70 °C.
  • Humidity Range: 5% to 95% non - condensing.
  • Dimensions: Width x Depth x Height (mm): 144 x 85 x 73.
  • Weight: Approximately 0.2 kg.

GE IC693MDL340

  • Input Voltage: Not applicable (operates on AC power source, output voltage is 85 - 132 VAC)
  • Output Voltage: 85 - 132 VAC, 50/60 Hz
  • Output Points: 16
  • Output Current: 0.5 A maximum per point, 3 A maximum per group
  • Response Time: Maximum 1 ms on - time, maximum ½ cycle off - time
  • Power Consumption: 315 mA (when all outputs are on) from 5 - voltage bus on backplane
  • Operating Temperature Range: 0°C to 60°C
  • Dimensions: Not fully specified, but typically suitable for standard PLC module installation spaces
  • Mounting Method: Can be installed in any I/O slot of a 5 - or 10 - slot baseplate in a Series 90 - 30 PLC system

GE IC300OCS110E

  • Input Voltage: The specific input voltage details are not fully provided, but it is known that it can support common industrial power supply voltages.
  • Output Power: The exact output power rating is not clearly stated in the available information.
  • Operating Temperature Range: Generally, similar power modules can operate in a range of -20℃ to +70℃, but this needs to be confirmed for the IC300OCS110E.
  • Protection Level: It may have a protection level of IP20 or higher, depending on the specific design.
  • Installation Method: Likely supports DIN - rail or panel - mounting, which is common for such modules.