Digital guide
You are here:
GE DS3800NPSL1A1A
Product Introduction: Published sources identify this part number differently. One source describes it as a Mark VIe DCS non-safety power supply logic module executing logic control and status management for non-safety devices. Another source describes it as a Mark VI Speedtronic 6U VME enhanced universal AC digital input board with programmable filter. A third source identifies it as a Mark IV DS3800-series RTD power supply board. The exact function must be verified against the original board label and rack documentation before replacement.
Detailed content
Technical Specifications (Enhanced Universal AC Digital Input configuration):
- Number of inputs: 16 optically isolated digital inputs
- Input voltage: 120 V AC or 240 V AC ±10% (auto-sensing)
- AC frequency range: 47–63 Hz
- Input filter: programmable 1 ms to 50 ms per channel
- Minimum detectable pulse: 1.2 ms (filter at 1 ms)
- Zero-crossing detection: < 200 µs
- Isolation voltage: 1.5 kV (channel-to-ground, channel-to-channel)
- Host interface: VMEbus (P1 connector), A24/D16 addressing
- Power draw: 5 V DC @ 0.76 A (typical)
- Operating temperature: -40 °C to +60 °C
- Dimensions: 6U VME (233 mm × 160 mm)
- Field connector: 64-pin D-Sub female (P2)
Technical Specifications (Non-Safety Power Supply Logic configuration):
- System series: Mark VIe
- Digital input channels: 16 (typical)
- Digital output channels: 16 (typical)
- Communication bus: Genius Bus
- Power requirement: 24 V DC (redundant)
- Operating temperature: 0 °C to 60 °C
- Scan cycle: ≤ 50 ms
- Protection rating: IP20 (cabinet installation)
Technical Specifications (RTD Power Supply configuration):
- Product line: Mark IV, DS3800 family
- Function: RTD power supply for gas turbine control systems
- Application: GE Mark IV turbine control cabinets
Functional Features:
- Non-safety device start/stop logic control (logic module configuration)
- 120/240 V AC auto-sensing with programmable filter (input board configuration)
- RTD excitation and signal conditioning (power supply board configuration)
- Independent operation isolated from safety-class systems
- Genius Bus communication with Mark VIe controller
- Front panel LED indicators for I/O status
Material Composition:
- Standard Mark VIe / Mark IV rack module construction
- PCB: FR-4 with conformal coating
- Connectors: VME 96-pin, gold-plated contacts
Structural Features:
- Standard Mark VIe rack module or 6U VME form factor
- Front panel LED indicators
- Rear terminal blocks or VME backplane connection
Application Scenarios: Gas turbine control, power plant DCS, industrial process control.
Working Principle: As a digital input board — it collects 120/240 V AC field signals, applies a programmable filter, performs fast zero-crossing detection, and reports state to the VME host controller. As a logic module — it acquires digital signals, processes them through internal logic, and outputs control commands via Genius Bus. As an RTD power supply board — it provides excitation power for RTD temperature sensors in the Mark IV turbine control system.
Installation Requirements:
- Install in the designated Mark VIe or Mark IV rack slot
- Genius Bus or VME communication cable must have terminating resistors at both ends
- 24 V DC power using redundant dual supply (logic module) or 5 V rail (VME board)
- Module address set via DIP switch, must not conflict with other modules
- Verify exact board revision and rack compatibility before installation
Usage Notes:
- Non-safety modules must not be used in safety circuits
- DS3800 boards are not interchangeable by appearance — verify full part number and revision
- Shut down and isolate rack power before handling — do not hot-swap
- Regularly inspect I/O channel LED indicators
- For RTD power supply configuration: check wiring and supply before condemning the board; verify sensor condition and calibration
