Digital guide

You are here:
  1. Home
  2. GE
  3. GE 531X139APMAKM6

GE 531X139APMAKM6

Product Name:​ GE Mark V / Mark VI 16-Channel Analog Input Module
Product Introduction:​ The GE 531X139APMAKM6 is a 16-channel analog input module for GE Mark V / Mark VI distributed control systems (DCS). It acquires 4–20 mA current and 1–5 V DC voltage signals from field transmitters, performing 16-bit A/D conversion with per-channel independent isolation, converting field analog signals into digital quantities that the DCS can process. It is the most fundamental data acquisition module in process control systems.
WhatApp
WeChat

Detailed content

Technical Specifications:
  • Channels: 16 analog input (AI) channels
  • Input signal types: 4–20 mA DC (2-wire) / 1–5 V DC
  • Input impedance: 250 Ω (4–20 mA mode) / >1 MΩ (1–5 V mode)
  • A/D resolution: 16-bit
  • Conversion rate: 10 channels/second (for all 16 channels)
  • Accuracy: ±0.05% of full scale (typical, at 25 °C)
  • Inter-channel isolation: 500 V DC
  • Common-mode rejection ratio (CMRR): >120 dB (50/60 Hz)
  • Wire break detection: Alarm when 4–20 mA signal falls below 3.5 mA
  • Zero drift: < 0.01% FS/°C
  • MTBF: 200,000 hours
  • Data update cycle: 100 ms (all 16 channels)
  • Operating temperature: 0 °C to 60 °C
  • Storage temperature: -40 °C to 85 °C
  • Mounting: VMEbus C-size slot (Mark V) / PMC slot (Mark VI)
  • Dimensions: 160 × 233.4 mm (Mark V VMEbus C-size); ≈ 150 × 180 mm (Mark VI PMC)
  • Weight: ≈ 0.55 kg
Functional Features:​ Supports both current and voltage signal types, switchable via software configuration without jumper changes. Each channel has an independent A/D converter for simultaneous sampling. Built-in cold-junction compensation supports direct thermocouple input (with a dedicated companion module). Wire break detection alarms when 4–20 mA signal drops below 3.5 mA. Engineering-unit linearization configurable for arbitrary input-output mapping. Front panel features 16 channel status LEDs.
Material Composition:​ Housing in die-cast aluminum with anodized finish (silver-grey); 6-layer FR-4 PCB with immersion gold process, independent layout per channel; 16-bit Σ-Δ type A/D converters (industrial grade); per-channel independent magnetic isolators; plug-in spring terminals in nickel-plated copper alloy.
Structural Features:​ Front panel provides 16 plug-in wiring terminals, 16 channel LEDs and 1 module status LED; rear side has system bus connector and power connector.
Working Principle:​ Field 4–20 mA or 1–5 V signals enter the module via wiring terminals, pass through input protection circuitry into a multiplexer, then undergo 16-bit Σ-Δ A/D conversion into digital quantities. The digital data is transmitted over the system data bus via optocoupler isolation for CPU reading.
Installation Requirements:​ Install in a VMEbus C-size slot (Mark V) or PMC slot (Mark VI) with proper seating into the backplane. Ensure ambient temperature stays within 0–60 °C.
Usage Notes:​ Per-channel independent A/D enables true simultaneous sampling. The module’s high CMRR rejects 50/60 Hz interference. Proactive spare holding is recommended as these are legacy components for Mark V/VI systems.

You may also like